Ownership Cost for 2012 Mitsubishi Outlander SE
Estimated: $39912 over the next 5 years
| Year 1 | Year 2 | Year 3 | Year 4 | Year 5 | Total | |
|---|---|---|---|---|---|---|
| Depreciation | $2657 | $1275 | $1116 | $1010 | $903 | $6961 |
| Insurance | $1837 | $1901 | $1967 | $2036 | $2108 | $9849 |
| Fuel | $1529 | $1575 | $1630 | $1696 | $1772 | $8202 |
| Maintenance | $2287 | $1597 | $1026 | $1067 | $2072 | $8049 |
| Repairs | $801 | $976 | $1110 | $1232 | $1426 | $5545 |
| Taxes & Fees | $881 | $881 | $881 | $881 | $881 | $1305 |
| Total Ownership Costs | $9992 | $7425 | $6978 | $7123 | $8394 | $39912 |
| Model year | COMPONENT | Complaint |
| 2003 | STEERING:RACK AND PINION:RACK | VEHICLE IN FOR SECOND REPAIR OF STEERING RACK. FIRST TIME THE RACK WAS REPLACED. REQUESTED REPLACEMENT AGAIN. VERY RARE FAILURE, YET TWICE WITHIN 30 K MILES? THERE IS A VARIABLE PULSING AND UNEQUAL PRESSURE WITHIN THE STEERING RACK HYDRAULICS. FIRST INSTANCE 16000, SECOND 31K MILES. ADDITIONALLY FAILED TIE ROD IN THIS SECOND INSTANCE. BEING REPAIRED AT UNIVERSITY MIT. IN BLOOMINGTON, INDIANA, AS IN THE FIRST INSTANCE. CALLED MIT. CUST SVC AND REQUESTED NEW RACK AND REPAIR OF TIE ROD AS WELL AS ALIGNMENT. THEY STATE THIS TO BE AN ISOLATED, TWICE STRUCK, DEFECT ISSUE AND NOT A CROSS PLATFORM/VEHICLE MODEL PROBLEM. *AK |
| 2012 | VISIBILITY | WHILE IN MOTION, AN ANCHORING SCREW HOLD THE PASSENGER SIDE VISOR TO THE ROOF PANEL FELL OUT INTO MY LAP. AS THE PASSENGER AT THE TIE, I CHECKED THE VISOR, NOTICING THE SCREW FELL FROM ABOVE AND NOTICED THE SECOND OF THE TWO ANCHORING SCREWS WAS NEAR FALLING OUT, ALSO. PREVIOUSLY, A SIMILAR SCREW HAD BEEN FOUND ON THE DRIVER'S SIDE FLOOR AREA, BUT THE LOCATION IT CAME FROM WAS NOT APPARENT AS THE VISOR MOUNT FROM WHICH IT FELL WAS HIDDEN BY THE POSITION OF THE DRIVER SIDE VISOR. CHECKING THE DRIVER SIDE VISOR, I NOTICED THE SECOND AND LAST ANCHOR SCREW WAS ALSO VERY LOOSE AND MOSTLY OUT OF THE TIGHTENING POSITION IT SHOULD HAVE BEEN IN. I ENVISION THAT IN A CIRCUMSTANCE WHERE AN AVERAGE DRIVER DID NOT NOTICE THE ANCHOR SCREWS WERE LOOSE FROM THE VISOR MOUNT OVERHEAD, THE VISOR COULD FALL ONTO THE STEERING WHEEL OF THE VEHICLE POSSIBLY CAUSING INABILITY TO STEER THE VEHICLE OR SURPRISING THE DRIVE ENOUGH TO CAUSE LOSS OF CONTROL OF THE VEHICLE. IT APPEARS THE TORQUE ON THE SCREWS WAS INCORRECT TO KEEP THEM SECURED, OR THE THREAD OF THE SCREW IS NOT CORRECT TO HOLD THEM TIGHT INTO THE VISOR MOUNTS, ALLOWING VIBRATIONS DURING NORMAL DRIVING USE TO ALLOW THE SCREWS TO BECOME LOOSE AND EVENTUALLY FALL OUT OF THE VISOR MOUNT BRACKET ALTOGETHER. I RESEATED THE SCREWS USING A SILICONE BASED GASKET SEALER TO PREVENT THE SCREWS FROM VIBRATING OUT OF THE BRACKET MOUNTS. HOWEVER, I CAN ENVISION THE SITUATION TO BE ONE THAT COULD CONTRIBUTE TO A CRASH. *TR |
Vehicle identification numbers: